8×10 chicken coop plans, plans include a free PDF download, material list, and step-by-step drawings.
8×10 Chicken Coop Plans – Gable Roof – Overview
8×10 Chicken Coop Plans – Gable Roof – Material List
Shopping List
Shopping List
Floor Frame
2 – 4×4 – 8′
2 – 4×4 – 10′
Front Wall
5 – 2×4 – 10′
3 – 2×4 – 12′
2 – 2×4 – 8′
Back Wall Frame
5 – 2×4 – 10′
3 – 2×4 – 12′
1 – 2×4 – 8′
Right Wall Frame
2 – 2×4 – 8′
3 – 2×4 – 12′
2 – 2×4 – 8′
Left Wall
8 – 2×4 – 8′
2 – 2×4 – 12′
Roof – Rafter/Truss
6 – 2×4 – 10′
6 – 2×4 – 8′
4 – 1/2″ Plywood – 4’x8′ sheet
Floor Deck
4 – 2×4 – 8′
1 – 3/4″ Plywood – 4’x8′ sheet
Inside Wall Frame
5 – 2×4 – 8′
Nest Box
Material for nest box not included (see “nest box plans“)
Siding – Wire Mesh – Roof Trim
Wire Mesh
5 – T1-11 Exterior Siding – 4’x8′ sheet
2 – 2×4 – 10′
2 – 2×4 – 12′
Front Door
5 – 1×4 – 8′
Right Side Door
3 – 2×4 – 8′
Trim
24 – 1×2 – 8′
Hardware
3″ deck screws
3 1/2″ galvanized nails
1 1/2″ galvanized nails
2″ galvanized nails
staples
1 1/4″ galvanized finishing nails
3″ galvanized finishing nails
4 – door hinge
2 – door handle
2 – door latch
Shingle
roofing felt
drip edge
roof tacks
roofing felt staples
Cutting List
Cutting List
Floor Frame
2 – 4×4 – 8′
2 – 4×4 – 10′
Front Wall
5 – 2×4 – 10′
6 – 2×4 – 6′
1 – 2×4 – 3′ 9″
2 – 2×4 – 3′ 5 1/2″
Back Wall Frame
5 – 2×4 – 10′
6 – 2×4 – 6′
2 – 2×4 – 1′ 9 3/4″
Right Wall Frame
2 – 2×4 – 7′ 5″
6 – 2×4 – 6′
6 – 2×4 – 2′ 5 1/2″
Left Wall
5 – 2×4 – 7′ 5″
5 – 2×4 – 6′
1 – 2×4 – 1′ 6 1/4″
1 – 2×4 – 1′ 10 1/2″
2 – 2×4 – 3′ 6 1/4″
Roof – Rafter/Truss
12 – 2×4 – 4′ 7 3/8″ (26.5 degree angle cut on one end)
6 – 2×4 – 8′ (63.5 degree angle cut on both ends in opposite direction)
4 – 1/2″ Plywood – 4’x8′ sheet (cut to size)
Floor Deck
3 – 2×4 – 7′ 9″
1 – 2×4 – 7′ 5″
1 – 3/4″ Plywood – 4’x8′ sheet (cut to size)
Inside Wall Frame
2 – 2×4 – 7′ 5″
5 – 2×4 – 3′ 4 3/4″
1 – 2×4 – 1′ 6 1/4″
1 – 2×4 – 1′
Nest Box
(see “nest box plans“)
Siding – Wire Mesh – Roof Trim
Wire Mesh (cut to size)
5 – T1-11 Exterior Siding – 4’x8′ sheet (cut to size)
4 – 2×4 – 4′ 7 3/8″ (26.5 degree angle cut on one end)
2 – 2×4 – 12′ (cut to size)
Front Door
5 – 1×4 – 8′ (cut to size)
Right Side Door
2 – 2×4 – 6′ 1 1/2″
2 – 2×4 – 2′ 6″
Trim
24 – 1×2 – 8′ (cut to size)
Floor Frame
Cut two 4×4’s to 8′ long. Cut two 4×4’s to 10′ long. Notch the ends 1 3/4″ deep. Assemble using 3″ deck screws.
Front Wall
Cut two 2×4’s to 10′ long. Cut six 2×4’s to 6′ long. Assemble as shown on illustration above using 3 1/2 nails.
Notch the wall studs 3 1/2″ x 1 1/2″ deep as shown on illustration above.
Cut three 2×4’s to 10′ long. Assemble as shown on illustration above using 3″ deck screws.
Frame the front door opening as shown on illustration above. Cut one 2×4 to 3′ 9″ long. Cut two 2×4’s to 3′ 5 1/2″ long, notch the top end around 2×4, assemble using 3 1/2″ nails.
Back Wall Frame
Cut two 2×4’s to 10′ long. Cut six 2×4’s to 6′ long. Assemble as shown on illustration above using 3 1/2 nails.
Notch the wall studs 3 1/2″ x 1 1/2″ deep as shown on illustration above.
Cut three 2×4’s to 10′ long. Assemble as shown on illustration above using 3″ deck screws.
Cut two 2×4’s to 1′ 9 3/4″ long, assemble as shown on illustration above using 3 1/2″ nails.
Right Wall Frame
Cut two 2×4’s to 7′ 5″ long. Cut six 2×4’s to 6′ long. Assemble as shown on illustration above using 3 1/2″ nails.
Notch the wall studs 3 1/2″ x 1 1/2″ deep as shown on illustration above.
Cut six 2×4’s to 2′ 5 1/2″ long. Assemble as shown on illustration above using 3″ deck screws.
Left Wall Frame
Cut two 2×4’s to 7′ 5″ long. Cut five 2×4’s to 6′ long. Assemble as shown on illustration above using 3 1/2″ nails.
Notch the wall studs 3 1/2″ x 1 1/2″ deep as shown on illustration above.
Cut three 2×4’s to 7′ 5″ long. Assemble as shown on illustration above using 3″ deck screws.
Cut one 2×4 to 1′ 6 1/4″ long. Cut one 2×4 to 1′ 10 1/2″ long. Cut two 2×4’s to 3′ 6 1/4″ long. Assemble as shown on illustration above using 3 1/2″ nails.
Install the wall frames to the floor frame using 3 1/2″ nails. Cut and remove the 2×4 on door opening, see illustration above for details.
Roof – Rafter/Truss
Cut twelve 2×4’s to 4′ 7 3/8″ long, cut a 26.5 degree angle cut on one end. Cut six 2×4’s to 8′ long, cut a 63.5 degree angle cut on both ends in opposite direction.
Cut out plywood gussets and assemble the roof truss as shown on illustration above using 1 1/2″ nails.
Place roof truss over wall studs and install using 3 1/2″ nails.
Measure, cut, and install 1/2″ plywood roof deck using 1 1/2″ nails.
Floor Deck
Cut three 2×4’s to 7′ 9″ long, install as shown on illustration above using 3 1/2″ nails.
Cut one 2×4 to 7′ 5″ long, install as shown on illustration above, toe-nail 3 1/2″ nails through the 2×4 and into the wall stud.
Measure, cut, and install the 3/4″ plywood floor deck using 2″ nails.
Inside Wall Frame
Cut two 2×4’s to 7′ 5″ long. Cut five 2×4’s to 3′ 4 3/4″ long. Cut one 2×4 to 1′ 6 1/4″ long. Cut one 2×4 to 1′ long. Assemble as shown on illustration above using 3 1/2″ nails.
Install the inside wall frame as shown on illustration above using 3 1/2″ nails.
Nest Box
Build the nest box, see “chicken coop nest box plans” for directions, and install using 3 1/2″ nails.
Siding – Wire Mesh – Roof Trim
Cut to size and install the wire mesh using staples.
Cut and install the siding to the left side of the coop using 1 1/4″ finishing nails.
Cut four 2×4’s to 4′ 7 3/8″ long, cut a 26.5 degree angle cut on one end. Assemble as shown on illustration above using 3″ finishing nails. Measure, cut, and install the front and back roof trim as shown on illustration above using 3″ finishing nails.
Measure, cut, and install the siding for the front and back wall, install using 1 1/4″ finishing nails. Cut the front door opening, the siding that has been cut out will be used to make the door.
Measure, cut, and install the siding for the inside wall, install using 1 1/4″ finishing nails. Cut out the door opening to the inside wall.
Front Door
Measure, cut, and install the 1×4 trim around door opening. Use 1 1/4″ finishing nails to install.
Use the siding that was cut out of the door opening to make the front door. Measure, cut, and install 1×4 trim on the door as shown on illustration above. Use 1 1/4″ finishing nails to install.
Add hinges, door handle, and latch, and install door.
Right Side Door
Cut two 2×4’s to 6′ 1 1/2″ long, notch the ends 3 1/2″ x 3/4″ deep. Cut two 2×4’s to 2′ 6″ long, notch the ends 3 1/2″ x 3/4″ deep. Assemble using 1 1/4″ nails. Cut wire mesh to size and install with staples.
Add hinges, door handle, and latch, and install door.
Shingles/Trim
Install roof felt, and shingles. Cut 1×2 trim and install.
These plans are great. Quick question… do you have plans for the ramp for the hens to get into the upper level?
Would like pdf of 8×10 chicken coop and the nesting box
I would like a copy of these plans. Thanks
Can you please email me a copy of the 8×10 chicken coop and nesting box plans? Thank you.
I’d like the plans.
I think it would be a lot easier to measure if you used inches instead of feet and inches
Personally, I like feet and inches.
please can you email me
8×10 chicken coop plan.
I think the industry standard is feet and inches. As this is a learning course (“Construction 101”), I think they hit the nail on the head.
Please email me these 8×10 chicken coop plans
Would love the plans for this and material list. Thanks
Thank you for taking the time to post and help others! I am thinking this project will be perfect for my daughter and I to conquer. Can you please email me the PDF and shopping list/tools needed. Will head to library and print out and begin the process 🙂
looks like a great DIY project
Please email me these 8×10 chicken coop plans. Thank you!
do you think i can have 8 chickens live in here add wheels and make it a tractor?
Currently have 16 in mine, this is way too large and heavy to be used as a tractor-type.
I extended the nesting box to full-width, works out perfect for us.
Please email me these 8×10 chicken coop plans
looks like a nice project
Can you send me plans for 8×10 chicken coop
Please email the 8 x 10 chicken coop plans
8×10 chicken coop
Can you please send me 10×8 chicken coop plans
Has anyone converted this to a 10 x 10 coop? If so can you help me convert the shopping list?
I love the plans but your website will NOT let me download the free .pdf
All these plans are awesome!
You just have to input any amount you’d like and hit that donate button, then, complete all details to add cart, then, after confirmation to your email address, you’re all set. 😉
Thanks construct101.com
Best woodworking site ever! 🤩🤩🤩
About how much does this cost to make
It cost about 1100 dollars with treated lumber
Email me the plan for this chicken coop, please. Thanks.
Could you please email me the pdf plans for the 8×10 chicken coop? I would love to build this! Thank you.
Download link is at the bottom of blog post.
Email me the Plans please
Please, could you sent me the PDF, this looks awesome and I would like to start this project. Thanks in advance
Please email me plans
how many chickens can this house? also is it absolutely necessary to use treated lumber?
Hello! Please can you email me these plans?
How many shingles are needed?
Please send me a copy of these plans, looks like what I’ve been looking for.
Please email plans. Thank you!
How do I go about getting some plans for a 12 X16 regular shed
please send me the plans
It says “PDF Download” right at the top of the screen. Easy Peasy!
PDF download doesn’t work
can you email me plans please
Pressure treated? Paint recommendation?
this is what i need!!! Could you send me the plan for the 8 x 10 chicken coop and the nest box too? I would like to built this! Thanks for your help!
Could you send me the plans for 8×10 chicken coop please.
Email me these plans please.
Email me the 8×10 chicken coop and the nest box plans.
Email me the 8×10 chicken coop and the nest box plans.
Please email me the 8×10 chicken coop and the nest box plans
Please email the plans for the 8×10 chicken coop. Thank you!
can you please send me a list of material needed to build this? something i can print out and take to the store and buy what is needed to build the chicken coop.
This so cool I’d sure like these plans
COMO PUEDO DESCARGAR LOS PLANO
Please email me the 8×10 chicken coop and the nest box plans
did you ever get the plans sent to you?
where do i get these plans for the 8×10 ??
Trying to download porch swing. Doesn’t download
i think these plans are perfect for what i would like to do.
can i get a set please
Could you email me the 8×10 plans please
Could you email me the pdf plans for the 8×10 and the nest box also? Thanks
كان رائع جميل جدا
Would like a copy of the plans. Thank You.
Jon Jonsson
8×10 plans thank u
can i please have the plans and the material list
great plans, had a blast making this.
i did move the nesting box door from opening on top to opening on the front. less scare/startle for birds.
i wish i would have moved the opening and nesting box 6-10 inches off the coop floor. birds can easily hop that and then you can have a deep litter method without getting chips/shavings in the nesting box.
Great build. Can you send me the PDF. We are starting the build ASAP. Thanks
This coop + run looks wonderful. Can you please also email me the plans and material list?! Thank you!!
I would really love a copy of the plans for this 8X10 chicken coop
I would like a copy of these plans please
I would very much like a copy of the plans for the chicken coop 8×10