Jack and Jill chair plans. These Jack and Jill seat plans include a free PDF download, step-by-step illustrated instructions, and a material list.
Jack and Jill Chair Plans – Overview
Jack and Jill Chair Plans – Material List
Shopping List
Shopping List
3 – 2×4 – 8′
9 – 1×4 – 8′
1 – 2×2 – 8′
1 1/4″ deck screws
3″ deck screws
8 – 3 1/2″ carriage bolt, nut, washer
4 – 3″ carriage bolt, nut, washer
Cutting List
Cutting List
A – 4 – 2×4 – 2′ 11 11/16″
B – 4 – 2×4 – 1′ 1 1/4″
C – 1 – 1×4 – 5 1/4″
D – 2 – 1×4 – 1′ 8 7/8″
E – 1 – 2×2 – 5′ 2 1/4″
F – 10 – 1×4 – 1′ 10 1/4″
G – 10 – 1×4 – 2′
H – 2 – 1×4 – 1′ 6 1/2″
I – 2 – 2×4 – 1′ 7 1/4″
J – 4 – 1×4 – 1′ 8 7/8″
K – 2 – 1×4 – 1′ 2 3/4″
Cut four 2×4’s to 2′ 11 11/16″ (A). Cut the ends as shown below.
Cut one end of the 2×4 (A) as shown on illustration above.
Cut the opposite end of the 2×4 (A) as shown on illustration above.
Cut four 2×4’s to 1′ 1 1/4″ (B). Use clamps to hold parts in place, drill holes, and assemble as shown on illustration above using 3 1/2″ carriage bolts.
Cut a 1×4 to 5′ 1/4″ (C). Pre-drill holes and assemble as shown on illustration above using 1 1/4″ deck screws.
Cut two 1×4’s to 1′ 8 7/8″ (D). Assemble as shown above using 1 1/4″ deck screws. Pre-drill holes and screw through (D) and into (B), the front arm rest (D) will have a 1/2″ overhang in the front.
Cut a 2×2 to 5′ 2 1/4″ (E), cut a 15 degree bevel cut on the 2×2 (E). Assemble as shown on illustration above. Clamp down the parts, drill holes through (D) and (E) and install 3″ carriage bolts.
Cut ten 1×4’s to 1′ 10 1/4″ (F). Pre-drill holes and install the seat slats (F) as shown on illustration above using 1 1/4″ deck screws.
Cut ten 1×4’s to 2′ (G). Cut two 1×4’s to 1′ 6 1/2″ (H). Cut two 2×4’s to 1′ 7 1/4″ (I). Make two sets. Assemble as shown on illustration above. Pre-drill holes and screw 1 1/4″ deck screws through (G) and into (H) and (I).
Install the back rest to the chair. Pre-drill all holes, screw 3″ deck screws through (A) and into (I), next screw 1 1/4″ deck screws through (G) and into (E).
Cut four 1×4’s to 1′ 8 7/8″ (J). Cut two 1×4’s to 1′ 2 3/4″ (K). Pre-drill holes and assemble as shown on illustration above using 1 1/4″ deck screws.
Install the table to the chair, pre-drill holes and screw 1 1/4″ deck screws through (J) and into (B) and (E).
The level of detail in the plan is great and the illustrations are crystal clear. Am looking forward to building these over the winter and enjoying some ‘lazy time’ next summer.
Is there a material list with this plan and a cut list that I’m just not seeing?
Never mind, duh. I found them.